|Air Leakage Resistance||a characteristic of a
closed window which restricts air
passage when the window is subjected to a differential
|Blow-Out||an assessment of
failure or permanent deformation of
any part of a window that would cause operational
malfunction(s) and/or endanger the user when
subjected to test pressures.
|Brush type seal||most commonly found on
sliders to facilitate the sliding
movement. It consists of a brush that fits into a plastic
track mounted on the sash or frame.
|Certification||the process through
which an independent body
ensures that standards have been met by means of
conducting audits and testing.
|Combination Window||a combination of two
or more complete window
assemblies of the same or different types, whose
frames are mulled together.
|Complete Tear Out||an installation
procedure in which the entire window
assembly is removed right back to the rough opening
and replaced with a completely new window.
|Compression Seals||seals that can be
squeezed tightly together between
the moving sash and frame.
|Condensation||the formation of moisture on the surface of the window.|
|Conductivity||the ability of a
material to conduct heat from the warm
side to the cold side.
|Conduction||heat loss in windows
that occurs primarily through the
edges of the glazing and through the sash and frames.
|Convection||heat loss that occurs
due to air movement between
the glazings of a window.
established by the Canadian
Standards Association for air tightness, water
tightness, wind resistance, condensation resistance,
forced entry resistance and ease of operation. It also
sets minimum requirements for all components and
their materials from hardware, insect screens and
weatherstripping to finishes and adhesives.
|Dew point||the temperature at
which the air can hold no more
humidity and it condenses to liquid.
|Double-Glazed Window||a window containing
two layers of glazing with a
uniform space in between the layers, usually two
panes of glass.
|Double Hung||both sash, top and
bottom in a vertical slider, open
|Emissivity||relating to windows,
the ability of the glazing to allow
radiation to pass through it.
|a scale rating the comparative performance of windows based on three factors: 1) solar heat gains; 2) heat loss through frames, spacer and glass; and 3) air leakage heat losses.|
|Frame||the associated head, jamb, sill and, where applicable, mullion and muntin that, when assembled, house the sash or fixed glazing.|
|Gas Fill||an inert gas, usually argon or krypton, pumped into the sealed unit replacing the air.|
|Glazing||the generic term for the transparent, or sometimes translucent, material in a window or a door. It is most often glass.|
|Head||the horizontal member forming the top of the frame.|
|Heat Loss||a basic law of nature that heat energy will move from warmer areas to colder areas.|
|High Emissivity||relating to windows, glazing that allows radiated energy to pass easily through it.|
|IGMA||Insulating Glass Manufacturers Alliance|
|Insulating Glass Unit||two or more panes of glass spaced apart and hermetically sealed in a factory.|
|Jamb||the upright or vertical members forming the side of the frame.|
|Light||another term for a pane of glass or glazing in a window.|
|Low Emissivity||relating to windows, glazing that restricts the passage of radiation through it.|
Low-emissivity, or low-E, coating
|a thin metallic layer, only several atoms thick, applied directly to the glazing surface the purpose of which is to reflect longwave energy back towards the source.|
|Mullion||a vertical or horizontal frame member that separates two or more sash, two or more fixed lights, or a combination of sash and fixed lights.|
|Muntin||a vertical or horizontal sash member that separates two or more lights within a sash.|
|Permanent Deformation||a change in shape or dimension which does not disappear when pressures are no longer applied.|
|R-Value||a measure of the resistance to heat flow through an object or material.|
|Radiation||heat loss that occurs through the window glass|
|Relative Humidity||the amount of water vapour in the air as a percentage of the maximum amount the air could hold at the same temperature.|
|Retrofit||an installation procedure that involves working within the existing frame and replacing the sash and the glazed unit with a new window.|
|Sash||a unit assembly of stiles and rails for holding glass with or without dividing bars and muntins.|
|SAWDAC||Siding and Window Dealers Association of Canada|
|Shims||wedges, usually about 2" wide used to position the window into the opening and ensure it is level, square and plumb.|
|Sill||the main cross or horizontal member forming the bottom of the frame.|
|Single-Glazed Window||a window containing just one layer of glazing, usually a single pane of glass.|
|Single Hung||only one sash, the bottom sash in a vertical slider, opens and closes.|
|Solar Gain||the positive contribution to the heating of a building's interior made by the sun's energy passing through a window.|
|Spacer||the strip of material that maintains uniform separation between the layers of glass in the glazing unit of the window.|
|Standards||minimum requirements, to which compliance is voluntary, for the components, materials and performance of windows.|
|Sweep Seal||a flexible fin usually made of rubber or polypropylene which is fastened to either the movable sash or the stationary frame and sweeps against the opposing component to form a barrier.|
|Meeting Stiles||the stiles of a pair of sash that meet when the sash are installed and in a closed position.|
|Thermal Break||an insulating material applied to a high conducting material to slow the transfer of heat.|
|Triple-Glazed Window||a window containing three layers of glazing with two uniform spaces in between the layers.|
|Warm Air Spacers||spacers made from insulating material such as foam, butyl, thermo-plastic, or thermally improved metals and therefore conduct significantly less heat energy than standard spacers.|
|Water Leakage||the penetration of water that would continuously or repeatedly wet parts of a building or components not designed to be wetted.|
|Weatherstripping||material around operating lights designed to reduce air leakage or water penetration or both.|
Awning Window: a frame with a sash that swings outward at the bottom.
Casement Window: a frame with a sash that may be fixed or hinged at the side to open in or out.
Fixed Window: a frame including a fixed light or lights. They do not open.
Hopper window: a frame with a sash that swings inward at the top.
Turn and Tilt Window: a frame with a sash that can either tilt inward like a hopper window, or to swing inward like a casement window.
Horizontal Sliding Window: a frame containing two sash and one or both sash operate by sliding sideways in the frame. The sash meet when closed.
Operable windows: are windows that open.
Projecting Window: a frame containing one or more sash, each of which swings horizontally to open in or out (Awning Window).
Storm Window: an exterior-mounted window intended for use in conjunction with a separate interior prime window.
Vertical Sliding Window: a frame containing two sash and one or both sash operate by sliding up and down in the frame. The sash meet when closed.
|Window Wise™||a national certification program that establishes minimum standards for windows, outlines best practises and trains installers on proper window installation procedures.|